Recent content by DaMenaCe

  1. DaMenaCe

    Hoist Motor Power

    @RonHebbard I picked up few adapters in case I run into reversed genders for Ground and Neutral! thanks for the heads up. Good Information!!
  2. DaMenaCe

    Hoist Motor Power

    Hey guys, been away from here for few days. I appreciate the discussion! This is exactly what I hoped for. @Gobokat i do have a controller that will be used to control the motors. I almost always carry a DVM in my bag pack. it seems logical to take measurement prior to connecting any...
  3. DaMenaCe

    Hoist Motor Power

    @RonHebbard That's good information right there.. Thanks a lot guys. I will go through the thread.
  4. DaMenaCe

    Hoist Motor Power

    Hey Lex thanks for the info. I hear you on getting support from the manufacturer. We have some lunch box style, 3 phase Motionlabs power distro with CS8364 style plug. I am familiar with the quality of the product and the support they offer but, with the way things are going right now, buying...
  5. DaMenaCe

    Hoist Motor Power

    Hey Philip... I see you are from Jersey. Happy to see that. From little that i know about 3 phase power distro, I assumed the power distro does not have any transformer so what you put in is what you will get out. Thank you for sharing that info. Mike, as i made the post on here, i was...
  6. DaMenaCe

    Hoist Motor Power

    Hey Chawlang, i understand it pretty well how and why the 208V comes about. i was just trying to figure what is the typical/common setup. if it is set up to have 208V per leg, i can see how. I am just concern about running the equipment far below the rated voltage range. The load applied on...
  7. DaMenaCe

    Hoist Motor Power

    Hmm, that's Interesting. I have a motor controller that reads Power In: 380 /220 v 3 phase. I was considering getting this distro linked below. It doesn't have cam lock connection points but that's something I can work out. I wanted to confirm if that 5 wire cam-lock tie in at the venue...
  8. DaMenaCe

    Hoist Motor Power

    Thanks, Lex. what happens when 240v 3 phase is needed?
  9. DaMenaCe

    Hoist Motor Power

    Hello All, Doing some research on power distro for chain hoist and controller. I have some understanding of 3 phase power but i am slightly confused. The Venu has a service line with 5 cam-locks ( Black, Red, Blue, White, Green.) Does anyone know what is the voltage between the two lines...
  10. DaMenaCe

    Came across a large eBay auction of older used gear

    Interesting. i will look into it. thank you, brother.
  11. DaMenaCe

    Came across a large eBay auction of older used gear

    How did you manage to do that? i am in the market for some wash fixtures.
  12. DaMenaCe

    9 Altman and ETC lighting clamps 100$ shipped.

    still have them for sale?
  13. DaMenaCe

    Conventional Fixtures ETC S4 Lens Tube. convert 19 > 36 ?

    Hey guys thanks for all the information. Derek those videos are awesome !! i have enjoyed them in past. SMH at 36 degree lense, being the only lense that requires 2 lenses. lol. That would be the case with MY Luck. oh well. in any case, thank you so much for the information, and i will look...
  14. DaMenaCe

    Conventional Fixtures ETC S4 Lens Tube. convert 19 > 36 ?

    Hey all, Just wondering if this is possible and economical? if so, are there any guides/tutorial / write up? please let me know. i have few lens tubes that dones't have any glass, so i am trying to "repair/repurpose" them. I am hoping to make them into 36degree lense tube. any...
  15. DaMenaCe

    Researching Power Distro Purchase

    Oh wow that makes lot of sense now. thank you so much for that information. So, correct me if i am not understanding this correctly but, you would use twist lock connections when power is being pulled over 2 or more phase lines?