Recent content by djsquizz

  1. D

    Pixel Mapping advice

    Hi everyone, I rented 9 Microh LED Tri Bars, 24 feet of 16" truss, and 2 Work LW265r stands for a highschool dance I'm doing in a few weeks. I plan on pixel mapping the led bars. I have chamsys magicq and a dmx interface, so patching them and programming them is not a problem. I was wondering...
  2. D

    Martin M-pc to Martin M-1

    Thanks for the advice! How do I know what playbacks/subs in M-pc correspond to the physical ones on the left side of the console though? The virtual console doesn't have the 12 faders and 8 buttons.
  3. D

    Martin M-pc to Martin M-1

    Hi, I'm working on a show in two months at a venue that I can not get into until the day before the show. They are running a Martin M-1 console, 6 mac250's, 20 led pars, a radiance hazer, and 36 channels of conventional dimmers. I got the in house tech guy to send me a sheet with all the dmx...
  4. D

    Powercon panel mount assembly problem

    Thanks! you were right! the 3/16" ones fit perfectly. I had to try 3 different electronics stores before i could find them though And oops, my mistake, it is a Neutrik NAC3MPA-1
  5. D

    Powercon panel mount assembly problem

    Hello all, I am having a problem assembling the Neutrik NC3FD-L-1 panel mount powercon connector. I have cut the end off of my power bar and as expected there is the live, neutral, and ground conductors. All are 14AWG. I put standard 16-14 gauge crimp disconnect connectors on each conductor...
  6. D

    Control/Dimming Chamsys MagicQ, Enttec DMX USB Pro, Windows 7 Help!

    It does say its an FTD driver in the details and the light is flashing so i'm assuming its working properly. I have Chamsys already set up for the interface, in the MagicQ owners manual it says you don't have to specify the "out uni" for usb interfaces though (Maybe that setting is only for...
  7. D

    Control/Dimming Chamsys MagicQ, Enttec DMX USB Pro, Windows 7 Help!

    When I go to switch the driver and select the downloaded one, windows tells me that "the best driver software for your device is already installed". does this mean that the driver I want has already been installed successfully? (the light on the enttec box does flash as it should when i open...
  8. D

    Control/Dimming Chamsys MagicQ, Enttec DMX USB Pro, Windows 7 Help!

    Sorry to be a noob, I'm probably missing something obvious. But where on the Enttec site are the drivers? Under the drivers tab on the website there is only one option for windows systems
  9. D

    Control/Dimming Chamsys MagicQ, Enttec DMX USB Pro, Windows 7 Help!

    About a month ago I downloaded the Chamsys MagicQ software and I've really started to like it. My Enttec USB DMX PRO just came in the mail so I can start using it for shows. After lots of reading other threads and posts all over the internet I know that I must install a different driver than...
  10. D

    Computer as EQ?

    When the interface is set to its highest settings, the latency is 1 ms (unfortunately this also uses alot of cpu power
  11. D

    Computer as EQ?

    I have a 4 input/ 4 output audio interface for my computer. does anyone know of a program that can make my computer act as a graphic or parametric equalizer. basically i want to run the master outputs of my mixer into the audio interface, have my eq on the computer, and run the output of the...
  12. D

    micing setup for a jazz band?

    the director for the jazz band at my high school asked me to do sound for the concerts they have during the year. the band consists of 4 flutes, 3 clarinets, 3 trumpets, 3 trombones, 2 tubas, 4 saxophones, 1 electric guitar, 1 electric bass, a digital piano, and a 5 piece drum kit. the problem...