Recent content by Dustin Druckman

  1. D

    Socapex wiring

    I have done this plenty of times I have just never come across a wire with only 13 leads. I usually see at least 2 grounds and then use a ground ring and I was clarifying if I should do something different with only 1 ground.
  2. D

    Socapex wiring

    I’m not doing anything with the box. It is going away. I am just using the cable from it to connect to a female Socapex.
  3. D

    Socapex wiring

    I am trying to covert a few stage pin drop boxes to socapex ends so that i do not need to haul these giant boxes up and down when tours come in. I opened the box up though and there is only one ground wire running in the cable and it is going to a bar in the box that the ground for each circuit...
  4. D

    Glaciator X Stream Making Floor Slippery

    I am using two Glaciator X Streams and they have recently started causing the floor in front of them to become very slippery. More than the normal amount. What do you thinks is the cause could it be the machine or perhaps the temp of the room? Any insight or ways to fix the problem or at least...
  5. D

    Control/Dimming Sensor+ Dimmer Rack Dimmers Failing

    Yes BG Dustin. I’ll try that but I’m fairly confident it is not an issue of comminication from my console. I am currently thinking it could be something wrong with my mains. Possibly not getting enough power from them. I will need to put a meter on them tomorrow.
  6. D

    Control/Dimming Sensor+ Dimmer Rack Dimmers Failing

    I am working with a Sensor+ Dimmer rack with R25D2 Dimmers. They keep on failing. Either not actually outputting power or not outputting consistently. The person that installed the rack entered the dimmer types in as R20D units. Could this be causing my problems?
  7. D

    LED House Lights Not dimming

    So my theatre installed a bunch of LED house lights 0-10V 1% dimming and gave me a few ELV10 dimmer modules and said it should work fine. Well surprise they don't dim. any ideas? The link to the units we have are below We are running 3 ETC sensor3 racks...
  8. D

    ETCnomad Via Etcnet

    Thanks. If I'm understanding you correctly I cannot output to net2 via Ethernet with the nomad. But if I was in a house running net3 I could output straight from nomad via Ethernet?If that is true can I go Ethernet out of my computer to a gateway running net3 and then put to DMX from the gateway?
  9. D

    ETCnomad Via Etcnet

    Thanks. If I'm understanding you correctly I cannot output to net2 via Ethernet with the nomad. But if I was in a house running net3 I could output straight from nomad via Ethernet?If that is true can I go Ethernet out of my computer to a gateway running net3 and then put to DMX from the gateway?
  10. D

    ETCnomad Via Etcnet

    I am running ETCnomad can i get my DMX through an exciting system with an ETCnet hookup. I tried plugging the ethernet cable in but it was not being recognized as being in a network port in network settings in the shell. I am running from a Mac.
  11. D

    Leprecon LD-360 and ETC ION

    Update: I am now acually at the theatre. It is a LD-360 HP. I have confirmed it is DMX. The new development is that it has the fast flash for address to high for anything less than adress 512 and slow flash for ok above 512. However when I send a signal from the board to address 1-1024 I still...
  12. D

    Leprecon LD-360 and ETC ION

    5pin, it does not have a terminator when it was tried by itself. But when it was wired in line with the rest of the system the line ended with a self terminating LED. Either way I have always used these units in the past without a terminator without trouble. I have talked with both ETC and...
  13. D

    Leprecon LD-360 and ETC ION

    When I plug into my sensor 3 rack I am able to control them as well as when I go direct into my LEDs so I know I am sending good DMX. At first I figured it was something wrong with my chain so I put the dimmer direct to the board. Also I have check all the lights and they work. This is the...
  14. D

    ETCnomad and submasters

    If I have the ETCnomad can i hook up and ETC 48/96 to be used as a submaster wing?
Back