MANDATORY TOOLS FOR ALL CALLS:
HAMMER
PLIERS
DIKES
SCREWDRIVER (slotted and phillips)
GLOVES
6"
CRESCENT WRENCH
POCKET KNIFE
MAP OF L.A. COUNTY
PEN OR PENCILS
MINIMUM TOOLS FOR CARPENTER SHOP CALLS
NAIL APRON
HAMMER (16oz.)
HAND SAW
DOVE-TAIL SAW
CHALK-LINE
SCREWDRIVERS (sloted and phillips)
SCREWDRIVERS (pump or
electric)
PLIERS
CRESCENT WRENCHES
STEEL TAPE MEASURE (25ft.retractable)
FRAMING SQUARE OR SPEED SQUARE
COMBINATION SQUARE
WOOD CHISEL (1inch width)
RIPPING CHISEL
PRY-BAR (super bar or
cat's paw)
NAILSETS (assorted)
DIAGONAL CUTTING PLIERS
PROTRACTOR
SLIDING T-BEVEL
BLOCK PLANE
WELDER'S MUST PROVIDE THEIR OWN HELMET
Manditory
call tool list for that local leaves something to be desired.
Hmm, starting out the list for say the sound guy to have a hammer would no doubt be a bad thing if a (are there IA sound guys?) This beyond the hammer jokes that could be made in making it fit. Hammer for me in general is a question of what ounce it’s weighted for and it’s head in that, yea you could have a 22oz. waffle head for much, but it don’t persay work as well at times for electrical boxes or finish nails. Same with “pliers” in that the heck, I don’t even own a pair of
slip joint pliers at home much less at work, to what does one mean “Pliers” that set on one’s multi-tool or a pair of “diagonal side cutting pliers” which don’t have a gripping
edge on them or a pair of 6" instead of 9" Linsemens pliers which one is attempting to do what ever with like say cutting a cable with. Oh’ you meant
slip joint pliers, they don’t cut cable - Next! Dikes is not “PC” I have been told. Best tell the IA’ it ain’t PC to specify something that could be considered offensive. This much less if I show up with a pair of electonics dikes and my task is to be cutting say some 10/3 cable, it ain’t gonna cut it. Yet I got these “minimum” tools, so pay me even if in doing the job I have to borrow from others in getting my job done as a “professional,” and many do buy from a 6" pair of “pliers” to the cheapest other tool they can in being useless as they can. Don’t help the show get done properly or most efficiently.
-Screw
driver - both slotted and phillips... Gee I tend to have fights with our guys about them if no #2 Philips in the drawer (beyond them not supplying their own tools), them using a #1 Philips for #2 screws in stripping them out in costing us money. Same with the proper
flat head screw
driver for the task, heck, can’t do an
Edison plug properly without both a 3/16" and 1/4" drive screw
driver if slotted yet there is no requirement for more than say even electronics #0 Philips or .5" slotted drivers to qualify for being on the job site. Yep, wee problems with that also.
Ya mean if I showed up with my like 18" long Klien 3/8" blade slotted screw
driver, that in comparing between it and the other ME at the shop and I is “Longer”, I can work a
call and in having that minimum requirement for slotted screw
driver be at all useful in using it for other than with say 5/16-18 or larger slotted screws? Anything smaller than that if slotted... pay me, let me borrow your tool? This much less the IA guy showing up with a 1/8 or smaller blade screw
driver - a
bit more demur in stature as it were, would be any more useful on an
Edison plug than I?
Dip switch, sure that guy, me I get the big stuff but it ain’t required so if anyone ain’t a
dip switch or
bolt turner on the
call - you pay to
send a runner out for tools while the crew seeks out donuts?
-Gloves... fine, what ever protects your hands without you cursing and wasting time picking slivers of wood out of them, don’t care, one would think quality but ain’t required in time being money as with hospital costs if the gloves you show up with
on-call don’t protect.
-6"
Crescent wrench is also improper terminology - you mean if I show up with a 8" Klien insul.
Grip adjustable wrench, I cannot work (assuming I were IA?) If given the “Crescent” brand name were more like
C-Wrench in slang term like Dikes, it’s improper also in that I believe Crescent makes some 6" wrenches that don’t expand out to 3/4" or 15/16" in need I could be useless on a
call, this much less I don’t accept a 6" wrench in general out of proper torque on a
bolt. I know if there ain’t some ‘IA deal with Crescent for specifically their 6" wrenches to be used exclusively as a brand, that I have at least a Craftsman 6" adjustable wrench which won’t work on a ½"
bolt and thus be useless for a crew
call. Are we than by specifying other than “wide jaw” 6" wrenches in assuming ability for a common torque on a
bolt other than the 8" standard, that it’s not important to get the work
call done?
What if nobody showed up with a proper adjustable wrench on a
call? Could happen as it’s not required to have proper tools so far.
-Pocket knife....... No comment other than dull knives assure hospital trips and are if needed problematic in needing of them. Still have my Boy Scout knife as with some of GrandPa’s pipe cleaning knives, so I’m all set.
-Now a map is awesome in concept. Just this past weekend pulled one out of my car and with my guys plotted out every single Menards, Home Depot, and Lowes location in the Northern Illinois and some Wisconsin areas. Amongst four runners that did the deal, we visited every at least Menards location in the are in the Home Depot versions being more expensive and Lowes versions pooping out sooner than the others for the part we were buying. In general a concept of a map might be “what we got here, why once here do we need a map for,” but I say great thing you have maps. Need to become a IA runner for parts instead of constructor of the show, you might be useful in having a map. Though if inspected at the door in having one I might not find such a thing as a map as important as other things important to my tool bag. You got here thus you seem to be able to find the place so I’ll assume you had a map.
-Pens and pencils... no Sharpees or paint markers of different colors so as to write on stuff beyond the
plot? While it’s often a challenge within a collected group of people to find just one with pen or pencil, also some form of other tool is often needed beyond that.
Definate holes in the manditory things I think, this plus this IA tool list for me is crap.
Onto the fun stuff...
MINIMUM TOOLS FOR CARPENTER SHOP CALLS
-Nail
apron = sound guys having a
nail apron would be fun.
16oz hammer = anyone that shows up with a 16oz hammer when I’m MC sweeps floors. Child hammer other than for specific instances.
-Hand Saw =
hand saw, really? Personal
hand tool to an extreme I would think in not being necessary and normally provided and sharp by the show if needed. This as = saw in general, my Leatherman has a saw on it... might take me an hour to hack
thru a two by four, but it’s a saw and what is required. Did you mean Shark saw, coping saw,
etc...? So don’t matter I suppose in nobody showing up with the required saw if needing to cut something if it’s useful or not? Got an awesome finite materials cutting saw with like 40 tooth blade to it.... it’s a saw, let me on the crew.
-Dove Tail Saw = I don’t even own one. What’s a Dove Tail Saw, I want one in the next step in my home furniture making operations assuming I don’t go with the
router jig thingie. Anyone really dove tail on a set these days? This beyond if I show up with a dove tail saw, don’t I qualify for the former in everyone looking at what it is for novelty sense? Ah’ crap, Knew why I never got to be Union, anyone let me in on the secret of what the secret handshake Dovetail saw is? Got Japan saws, Shark Saws, Dad’s old coping saw about to be replaced in that it just don’t hold a blad and other saws but no dovetail saw, and I want one.
-Chalk
line is a good concept to have both as
plumb bob and
snap line, does the show site provide chalk for it? Out of chalk... gee that’s just too bad you cannot get on the
call.
-Screw
driver, Ibid
-SCREWDRIVERS (pump or
electric), Yay the
Yankee or ratcheting screw
driver in it’s user being just as useful as the cordless drill using techie! No matter the labor and man/hours, that guy using the
yankee in sticking with it no doubt is just as cost effective and never runs out of batteries in using it - this granted he wastes time in explaining to everyone around in how it works and in how it is just as efficient. Need to screw down a plywood
deck, that
Yankee guy is going to be just as useful as that automatic feed screw driving guy with battery back pack guy on the crew. Sometimes perhaps I’m a
bit dim.
-again with the “pliers” in general. What no difference beteween needle nosed and 9" Linsesmens’?
- Crescent Wrenches - at least if a carpenter you had at best by definition have more than one.
-25' tape measure... best be able to prove it retracts and don’t stop short on that about three feet
mark if it has run into trouble in winding in a past life. Those with tape measures that don’t fully retract one might assume need not apply. Don’t matter the tape measure of course if a wee
bit short, just need retract of course. Ah’ but it’s a tape measure at least which is important. Thought of mocking one of my assistant’s 12' tape measure in a guy type of way today, but on the other
hand he has on and other’s on my staff don’t have one they can produce. Tape measure a good thing. This as required for all especially a good thing. Do they all show up to the
call with one and ready to use it?
- Fraiming Square or Speed Square.... What’s the defination of a “speed square” and or would my 12x9 small square qualify for a “fraiming square” This much less assuming it’s a IA tool list the fraiming square is assured to be dinged into square. 1/8" thick verses 1/4" thick square for sawing purposes = a 1/4" thick speed square is much more useful. This one of 12" instead of 6" size.
-Combination Squares are perfect instruments of use. Who did or when were they invented? What are they based off of in concept? Great tool, one - my Dad’s at work, a newer one at home. I prefer Dad’s, though the reverse side should go metric.
Anyone really show up on site wit one of these or a “Tri-Square” and would such a term be different?
-Chisel 1" width.... the heck use is a 1" width chisel and do it need to be sharp? One of my assistants is a union carpenter by trade... asked him this past summer to chisel out a door hinge for me on a special project and he had no idea. I vote a 3/4" or say ½" chisel is often more useful if sharp for more than barbaric work. Got this reinforced and no longer sold Wagner
Power Scraper with modified oak/steel handle for pounding that’s knife sharp and like three inches wide, if I showed up with one of them plus say a ½" chisel that’s also sharp but no 1" chisel, verses one that showed up with a dull chisel that’s 1" who gets the job might be something to work on. This plus does everyone show up to the job site with a chisel? Thats’ fascinating as I’m not seeing any need for them to show up with a matt knife as normal for use also. Good sharp knife often is also needed for good chisel work.
-Ripping Chisel, oops, I suppose My custom built Wagner
Power Scraper blade set on a
hand made oaken handle with 1/4" steel reinforcement handle is something everyone spends hours upon hours on in creating - cuts
thru pneumatic staples or even drywall screws with
ease.... Yep, everyone has one, much less keeps it sharp. Otherwise such ripping chisel, might be not knowing the term of ripping chisel for sure - know ripping saw blade but not in reference to a chisel, guess that shows skill
level type of thing in being a term I’m not ready for yet, but if in general a thing that’s a say
laminate tile scraping chisel, one that say has a handle that accepts a broom handle... yet to see others to show up on a job site ready to go with their
power scrapers - but it would be nice in that they are also useful for clout nails. I’m thinking this IA rule is by way of tool requirements thus requiring a long
flat plat of steel that can also be used for clout nails, a three inch wide blad for scraping up
laminate asbestos tile while attached to a broom handle for this requirement as per “ripping chisel.” This or they if not the definition in term, perhaps those chisels used for opening up padlocks or in breaking
thru staples or nails, them chisels no longer servicable for wood scrapint, instead for use once dinged for ripping up the wood scraped while used thus the “Ripping Chisel” term that it would seem local dialect I am attempting to inerpite.
-PRY-BAR (super bar or
cat's paw), Sorry, don’t own any of them. So you mean if I have a “
Wonder Bar” and a few other types of pry bar, I cannot work on this job site? What’s those brand names paying to the Union to demand all showing up for work have those tools anyway? Good ‘Q of the Day’ what either of these tools are in name to what they look like recognition. Know I wouldn’t recognize either by look. Are they as a specific type in brand as with Crescent tools superior as in general to all others? Or is this just some type of being specific in a lazy type of way and in being specific in that way making for a
system of contro nobody’s going to follow in listening to these minimum tool requirements anyway “but it sounding really really good?”
-Nail sets... yea, that’s useful for a proper hammer - no matter the weight in say having a 22oz waffle head and not hitting the
nail down all the way in using such a
nail set. This espcially if using pneumatics and they are under lower pressure or dirty or punching
thru hard wood, one needs to have various sizes in punching them heads in. This plus needle nosed pliers to rip off the as it were slightly off aim or hitting something hard
nail or prong sent astray, plus say a 1"
putty knife to
cover with what ever the hole by it left behind plus sand paper in what’s left of the hole in doing damage. Hmm... flexible 1"
putty knife... that’s a good thing also.
-Diagonal Cutting Pliers, for a carpenter
call I would think at least an exception for “carpenters pinches” especially case hardendered versions of them would be acceptable. This if not the off the shelf and not say Journeyman 2000 hardened Klien version, gonna be dull and useless for a carpenter after some use, so why require what’s dull other than specifying what might be useful?
Take a typical 6" Ace Hardware diagional side cutting plier and cut one drywall screw with it. Cut the same screw with a hardened 8" Journeyman hardened pliers and one will see that even if at double the price, someone shows up on a
call with a now dinged set of dikes - as it were, someone shows up with a tool ready for another cut as needed without a definition as to who gets in the door otherwise. Can have dikes dull as crap and short as sh... but if you got them, that’s all good in being another useless person potentially on the jobsite mixing with the Pro’s there to do their career as opposed to collecting their pay check by being there.
-Protractor... What’s a protractor.... I know I have what one is - at least one or a few that might qualify but it just don’t come to mind. Been years since I heard that term in using it even as a
Master Carpenter of my field. I think I have one dating back to like 1982 in having drafting classes but just can’t remember what such a thing is. Should I need work, thowing such a ancient thing into my bag will be really necessary.
Sliding T-Bevel.... I got nothing. I do have a sliding angle degree tri-square, and rarely use it, even marked on it’s markings what is the accurate side of the scribed
line for it - this in given like a 1mm
line only the
edge of this
line being as it were square in what I found how many did end for end test their if that’s what it is sliding T-Bevel? This much less own one? And don’t one in having this thing also qualify for also having a “combination square”?
-Block plane... Own lots of them from antique to new. Used to be able to make them function with a curl, curse them years later in just not getting them as concept in grabbing another tool.
-Welders in own helmets but in providing them - replacement shields, gloves, arm guards, and aprons? Such gear - much less lenses for the helmets I would say are shop provided - tools specific and prefered to the welder those tools they provide. Sure if they want their own helmet - and dependant on type of welding done for
lens or protection, it’s recommended but also provided. Weldings’ separate than something off the street and to crew
call with someone showing up with crap chapest possible that don’t last from someone that welds with a certification not necessary for this IA list, no doubt in having the cert, with their own tools beyond that of a helmet.
I view this tool list a joke and why in many cases gear comes back crapped up after traveling about to venues by way of barbarians using the gear.