240) What is the safe working load or maximum live load in the basket of a Condor?
571) What is the approximate proper drilling speed of an 1/8" high speed steel bit in mild steel?
572) What is the approximate proper drilling speed of an 1/8" high speed steel bit in aluminum?
573) What size nut uses a 9/16" wrench? What size uses a 11/32" wrench?
575) A groove of M or #3 on a Nico Press is good for what size oval seeve in wire rope?
577) Why is using a C-Wrench at its widest setting bad?
578) Soldering iron tips may become pitted for what reason?
579) What is the maximum output size of generator which does not require a grounding rod according to the NEC?
580) Why are tubing cutters not preferred for use with conduit?
581) The starting current of a gasoline generator can be up to how many times that of the normal running current for small motors?
582) What is the relationship between pitch diameter and rotational speed on a gear?
583) To find the driven shaft speed, you should multiply the driving pitch diameter by the speed of the driving shaft and divide or multiply by what?
584) The alignment of a V belt should be no more than how many inches out of alignment for each 12" of center distance?
585) When operating a pressurized tank such as an propane tank, what is the standard amount of turns you should open the valve with?
586) When operating a fork lift on an incline with a load, you should do what?
587) What two rules for personal safety are required for the operator when operating a fork lift?
588) What size is the standard phillips screw driver?
589) What is the best size slotted screw driver blade for a #6 screw?
590) What part of a drill bit is called the tang?
591) If your soldering iron tip does not heat up the material well, application of a little A)flux or B) solder to the tip of the iron will aid in transferring the heat to the material.
592) On a cordless screwdriver, the torque setting is approximately 1.1 inch-pounds per step for 21 steps, given a total of 39 inch pounds max torque, what would the approximate proper setting be for use on a slip plug? Note: the torque is to a #8 brass screw clamping down of #12 AWG stranded wire.
593) When should you run down the charge on your cordless tool batteries?
594) What type of charger is best for the battery: a 3 hour charger, a 1 hour charger, or a 15 minute charger? Why?
595) What is the maximum drill bit diameter of most cordless drills in steel?
596) Explain the steps and materials involved in using a screw extractor?
597) How does a clamp-on style amp meter or voltage sniffer work?
598) When using a C-Wrench, which is the right side of the wrench to be pulled in the direction of the turn, the side with the adjustable jaw, or the side with the large cast fixed jaw?
571) What is the approximate proper drilling speed of an 1/8" high speed steel bit in mild steel?
572) What is the approximate proper drilling speed of an 1/8" high speed steel bit in aluminum?
573) What size nut uses a 9/16" wrench? What size uses a 11/32" wrench?
575) A groove of M or #3 on a Nico Press is good for what size oval seeve in wire rope?
577) Why is using a C-Wrench at its widest setting bad?
578) Soldering iron tips may become pitted for what reason?
579) What is the maximum output size of generator which does not require a grounding rod according to the NEC?
580) Why are tubing cutters not preferred for use with conduit?
581) The starting current of a gasoline generator can be up to how many times that of the normal running current for small motors?
582) What is the relationship between pitch diameter and rotational speed on a gear?
583) To find the driven shaft speed, you should multiply the driving pitch diameter by the speed of the driving shaft and divide or multiply by what?
584) The alignment of a V belt should be no more than how many inches out of alignment for each 12" of center distance?
585) When operating a pressurized tank such as an propane tank, what is the standard amount of turns you should open the valve with?
586) When operating a fork lift on an incline with a load, you should do what?
587) What two rules for personal safety are required for the operator when operating a fork lift?
588) What size is the standard phillips screw driver?
589) What is the best size slotted screw driver blade for a #6 screw?
590) What part of a drill bit is called the tang?
591) If your soldering iron tip does not heat up the material well, application of a little A)flux or B) solder to the tip of the iron will aid in transferring the heat to the material.
592) On a cordless screwdriver, the torque setting is approximately 1.1 inch-pounds per step for 21 steps, given a total of 39 inch pounds max torque, what would the approximate proper setting be for use on a slip plug? Note: the torque is to a #8 brass screw clamping down of #12 AWG stranded wire.
593) When should you run down the charge on your cordless tool batteries?
594) What type of charger is best for the battery: a 3 hour charger, a 1 hour charger, or a 15 minute charger? Why?
595) What is the maximum drill bit diameter of most cordless drills in steel?
596) Explain the steps and materials involved in using a screw extractor?
597) How does a clamp-on style amp meter or voltage sniffer work?
598) When using a C-Wrench, which is the right side of the wrench to be pulled in the direction of the turn, the side with the adjustable jaw, or the side with the large cast fixed jaw?